熱門關鍵詞: 液壓升降平臺 導軌式升降機 移動式升降平臺 固定式升降機 鋁合金升降平臺
安裝固定式升降平臺,,需要有垂直的一個安裝位置,,來進行設備的安裝。由于很多客戶都是加裝的升降平臺,,所以安裝環境來講一般都沒有單獨預留,,很多時間都需要臨時的進行處理的。下面就給大家分析一下固定式升降平臺安裝環境,。
1,、室內井道安裝:這種是對于預留位置的客戶,安裝的時候有甚少兩面的靠墻位置,,相對比較安全,,也比較方面。缺點是由于井道的位置限制,,設備的導軌和油缸進出會十分的不方便,,預留井道的客戶在定制設備的時候要提前告知井道的尺寸,以方便進行定制,。
This position is reserved for customers, there is very little time to install both sides of the wall position, relatively safe, but also more respect. The disadvantage is that due to the location restrictions hoistway, rails and equipment out of the cylinder will be very inconvenient, reserved hoistway customers to customize the device to be informed in advance when the size of the hoistway to facilitate customization.
2,、室內切樓板安裝:如果室外沒有安裝的位置,而室內又沒有預留井道就要考慮切割樓板了,。切割樓板要注意安裝位置的大小,,根據設備的大小進行切割,在切割的過程種不要發生偏離的現象,。因?yàn)闃前迨乔懈畹?,所以上下貨的時候要注意樓板的承重性,可以考慮對四周進行加固,。
If no location outdoor installation, while the interior has not reserved the hoistway should consider cutting the floor. Note that the size of the slab cutting installation position, according to the size of the device cut in the cutting process do not deviate species phenomenon. Because the floor is cut, so pay attention when the goods up and down the floor load bearing properties, could be considered for the four weeks reinforcement.
3,、室外安裝:升降平臺室外安裝要考慮到靠墻的問題,最好有靠墻的情況下再進行安裝,。如果沒有靠墻的位置,,則要考慮是否有安全的固定點,以防止設備沒有固定穩定而造成的搖擺,。
Outdoor installation should take into account the issue of the wall, there is the case of the best against the wall before installation. If there is no location of the wall, will have to consider whether there is a fixed point security to prevent the device does not have a fixed and stable swing caused.