重慶升降機漏油問題是經常碰到的問題,。漏油的原因是錯綜復雜的，主要是由于液壓元件的質量，振動,，腐蝕,，壓差，管路的連接,、使用維護不當引起,，對于少量的漏油是不可避免的，這是由于液壓傳動的本質所決定的,。漏油量超過規定指標的現象由于外漏,，一般能立即察覺出來，主要變現在壓力下降,，速度驟變已經地面或者機器表面有積油,，設備需要經常補油才能恢復高空作業平臺之前的高度。一旦漏油就要停機進行修正,，因為急性運轉只會把系統抽空并使泵的機件損壞,。

1、液壓油是在一個密閉的環境中運行的,，油質泵站打壓被注入油缸內一般的壓力大于等于12pa,，液壓油被打壓加油缸的摩擦就會產生熱。發熱膨脹的油質加站泵對液壓油的壓力,，若有密封不嚴的話,，液壓油便會漏。
Hydraulic oil is in a closed environment, running, oil pumping station pressure is injected into the cylinder pressure is generally greater than or equal 12pa, hydraulic oil is fueling pressure cylinder friction will generate heat. Expansion of oil plus heat pump station hydraulic oil pressure, if Mifengbuyan words, the hydraulic oil will leak.

2,、升降平臺過多的油管和接頭會加大漏油的現象,。油管內的壓力一般為12pa，而且油路接頭一般用三通和對絲連接,，油管內壁直徑在9mm左右,，而接頭的內徑不過7mm。如果油路內管過長,，接頭多就又加大了漏油的幾率,。
Ningbo lifting platform excess tubing and fittings will increase the leakage phenomenon. Pressure tubing is generally 12pa, and the oil is generally used three-way connector and wire connections,tubing wall diameter of about 9mm, and the inner diameter of the joint, but 7mm. If the tube is too long in the circuit, and more on the joint probability of oil spills has increased.

3、升降平臺設備長時間的運轉,，油質變化,，加上保養修復不嚴格，會使管道內壁產生污物,，加大油路內的壓力,，對絲、接頭間的復合墊,、密封圈老化也會加大漏油的機會,。
Ningbo lifting platform equipment long run, oil changes, coupled with the maintenance repair is not strict, will produce pipe wall of dirt, increase the pressure inside the oil on the wire, the joint between the composite mat, seals aging will increase the chance of oil spills.